Crossover Steering Kit w/ Pitman Arm and Threaded Drag Link / Tie Rod
This kit does NOT include the passenger side High Steering arm but does include the Pitman arm, thick wall DOM tie rod and Drag Link pre-threaded with proper Right and Left hand 7/8 in x 18 TPI, and Genuine MOOG Tie Rod ends and Double Pivot Drag Link Ends. If you also need the Dana 60 Hi Steer arm it is available separately so we can properly drill and taper it from the bottom up or top down based on your intended lift height.
This kit uses double pivot drag link ends at both the pitman arm and hi-steer arm to maximize the amount of articulation that can be achieved. The tie rod ends are standard Chevy "1 ton" ends. We only use genuine MOOG parts and all our tie rod and drag link ends come with jamb nuts.
For both the tie rod and drag link tubes we use 1.25 inch O.D., 0.219 inch wall DOM tubing that is pre-cut and threaded to the required length for our low boy kit by default however we can make them to any length. Simply thread in the rod ends, set your toe and center your steering wheel, and you are done!
Our pre-tapped tubes have also have machined flat spots for using a wrench to allow easy adjustment of the tie rod and drag link and double wrench tightening of the jamb nuts.
IMPORTANT - When building these tubes, we tap our threads 2" deep. We know that the tie-rod end we include do not thread all the way in which is why you need to giv us the center to center dimensions of the holes for the tie rod and the drag link. We calculate the length of the tube we need to machine and we allow you room to adjust for toe and steering wheel center.
Pitman Arm
- Non-Indexed Fully Splined Drop Pitman Arm
Drag Link
- MOOG Double pivot drag link end ES2027L
- MOOG Double pivot drag link end ES2026R
- Pre-measured and tapped length of 1.25 inch x 0.219 inch DOM tubing with wrench flats
- Two Jamb Nuts
- Two Cotter Pins
Tie Rod
- MOOG ES2233L tie rod end
- MOOG ES2234R tie rod end
- Pre-measured and tapped length of 1.25 inch x 0.219 inch DOM tubing with wrench flats
- Two Jamb Nuts
- Two Cotter Pins
READ FULL DETAILS HERE
IMPORTANT INFORMATION AND DISCLAIMERS
It is the sole responsibility of the installer, purchaser, and end user (collectively, hereinafter "Buyer") of any product to verify the legal use of any product and to employ the correct installation techniques to ensure proper function of the product as well as use of the vehicle within the constraints of all applicable laws and the constraints of the original vehicle design or by making sufficient modifications to the vehicle to support the product being installed. Performance Group LLC, it's directors, officers, members, employees, agents, representatives, successors, affiliates, assigns, and/or volunteers (collectively, hereinafter "Seller") are not liable for damages of any kind for any reason, and hold no liability for any product failure for any reason, including possible fines for illegal or improper product use or installation. The Seller makes no claims or representations and offers no certification or warranty of legal use of any product for the Buyer's application.
EMISSIONS WARNING
Some Products sold by the Seller are Intended for Legally Sanctioned, Organized Competition and Race Use Only and may not be legal for use on any registered vehicle in the United States. Some Products are not legal for sale or use in the state of CA, or states adopting CARB standards, on any emissions controlled vehicle unless the product has a CARB EO # or the product classification is specifically exempted by CARB.
PRIOR TO PURCHASING THIS PRODUCT, YOU MUST CONSENT TO THE TERMS OF A CUSTOMER NOTIFICATION AND DISCLAIMER OF LIABILITY FORM BY ELECTRONICALLY ACCEPTING SUCH TERMS AT CHECKOUT.
ATTENTION CALIFORNIA RESIDENTS
Proposition 65 WARNING: Some of the products sold by the Seller through this website and other sales channels contain, or may contain, chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. This does not mean that the products sold will necessarily cause cancer or reproductive harm. While the Seller believes that the products they sell are not harmful when used as designed, you should take all necessary precautions to protect yourself such as wearing gloves, appropriate clothing, and respiratory protection when handling the products. Never machine, grind, weld, install, or otherwise modify or operate any of these products without wearing proper protective gear and apparel. You should also exclusively use the product for the intended purpose, don’t handle or work on the product without proper protection and don’t eat, lick, or otherwise put these products into or on your body. We provide these warnings as a result of the California law and for your protection. You can verify the current list of chemicals here: https://oehha.ca.gov/proposition-65/proposition-65-list
PRIOR TO PURCHASING THIS PRODUCT, YOU MUST CONSENT TO THE TERMS OF A CUSTOMER NOTIFICATION AND DISCLAIMER OF LIABILITY FORM BY ELECTRONICALLY ACCEPTING SUCH TERMS AT CHECKOUT.